42 not categorized PORSCHE 356 BUSHINGS SUSPENSIONCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1998-05 (includes uncategorized and accessory items) FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$69.30
Make a selection 150PB00619 Replace worn-out original stabilizer bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. Sold individually. 2 necessary per car. Please note: this fits 911 models from 1965-73 if fitted with 19 mm original stabilizer bars. It also fits the 1975-77 930 turbo model if fitted with 19 mm original stabilizer bars.
$57.20
Make a selection FVD33300905ATK Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this does not fit cars with the g50 transmission.
$312.40
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD34105307R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 2 are necessary per car. Please note: this does not include the lower control arm, the picture circled in red is just for reference. General Fitment911 GT3 2003-05911 TURBO/GT2 2001-05 911 1998-05 BOXSTER 1997-04
From $98.92
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$152.90
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection RS18 Set of two sealed monoball cartridges - front or rear. Most Porsche owners today, especially those of us who take our cars to the track, have equipped our cars with tires much wider and stickier than stock, which allows higher g-forces to be achieved in cornering and braking. During that type of hard driving, rubber suspension bushings are compressed and flexed by the extreme loads being put on them, defeating your car's finely tuned alignment settings, thereby reducing your braking and cornering potential. Monoballs are a downside-free improvement; because they eliminate four important sources of suspension slop without making your car's ride harsher. Your Porsche will handle and brake with greater precision...(choose a part on the right to read more) General FitmentBOXSTER 1997-04BOXSTER 2005-08 CAYMAN 2006-08 911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$250.00
Make a selection S1116 For a perfect fit, reliability you can depend on, full adjustability, and optimum performance, the factory GT3 swaybar is the best on the market. We have packaged them together with new bushings and our adjustable drop links to provide you with a wining combination. The light weight hollow 26.8mm od sway bars are half the weight of a solid bar with the same stiffness. Complete with fully adjustable front drop links to eliminate suspension preload. Correctly sized, precision, teflon-lined rod-ends for smooth and quiet operation, long life, and high reliability. No wear and rattling problems, like those seen with other designs, due to undersized or low quality rod ends. All necessary hardware is provided in zinc ...(choose a part on the right to read more) General Fitment911 1998-05BOXSTER 1997-04
$718.75
Make a selection TS00001 Torque solution adjustable thrust arm bushing kit replaces the factory,rubber bushings on the wheel-end of the control arms with abilletaluminum bushing,this will allow forbetter handling and most importantalso allows for the adjustment of General Fitment911 1998-05
$258.19
Make a selection TSPOR005 Torque solution solid rear subframe bushings General Fitment911 1998-05
$172.11
Make a selection 99634104306 Forged arm w/ urethane bushing View/Change Diagram
From $153.15
Make a selection FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$746.90
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$715.00
Make a selection FSBA19 The light-weight hollow sway bars are half the weight of a solid bar with the same stiffness. they are fabricated from aircraft-quality 4130 chrome moly alloy steel and heat treated to maximize strength and reliability.
$595.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |